widely used air driven liquid pump pump types for machinery

Compressed Air Driven Liquid Booster Pump-DGGD Series

We offer the most complete range of Air driven liquid pump models in the industry measured for:

Capability of ultimate pressure, flow or output horsepower.

widely used air driven liquid pump pump types for machinery-1

Compatibility with a broad variety of liquids, such as oil, water and chemical applications.

SUNCENTER pumps are air driven at a drive air pressure of 1bar to 8bar (14.5 psi to116 psi) by the normal air compressor. Basically the principle of operation is similar to a reciprocating amplifier where control of the piston at the end position is regulated by a pilot operated 4/2 way valve.

Suncenter pumps feature a large air piston joint to a smaller diameter plunger. The pressure ratio is the difference of these two areas and is the method of determining maximum outlet pressure. Higher pressures obtained by using higher pressure ratios.Suncenter model numbers reflect the pumps nominal pressure ratios， while the technical data indicates exact ratios. The outlet pressure is easily to set through a simple air regulator. By multiplying the pressure ratio by the available shop air pressure, the nominal liquid pressure can be calculated.

SUNCENTER pumps are self priming. In general it is not necessary to use an air line lubricator. The liquid to be pumped flows into the suction chamber by the up-stroke of the drive piston. By this suction effect, the inlet check valve is opened and the outlet check valve is closed. The down-stroke generates the pressure at the liquid side. The inlet check valve is closed and the outlet check valve is opened by the generated pressure. SUNCENTER liquid pumps cycle automatically, where the pressure is built up the numbers of cycles slow down, the pump stops automatically when the output pressure forces are equal. The pump restarts with a slight drop in the outlet pressure or an increase in the air drive pressure. Pump performance can be affected by a number of conditions, such as freezing of muffler or pilot valves (which is caused by moisture in air lines), inadequate inlet air line sizes and dirty filers. Don’t reduce the indicated port sizes and consult SUNCENTER for exact flow conditions not shown in charts.

widely used air driven liquid pump pump types for machinery-2

DGGD Series Liquid Pumps(Double acting, single air drive head)

widely used air driven liquid pump pump types for machinery-3

◪ They are characterized by the same features as the DGG pumps single acting, single air drive head types, but they have less pulsations and deliver approx. 50 % more flow.

Model	Pressure Boost Ratio	Driven air pressure PL	Formula to calculate outlet pressure	MAX Outlet Pressure(bar)*	Liquid inlet Connection	Liquid outlet Connection	MAX Flow (L/min)**
DGGD4	4:1	2-8 bar	4XPL	32	NPT1/2	NPT1/2	70.00
DGGD6	6:1	2-8 bar	6XPL	48	NPT1/2	NPT1/2	48.60
DGGD10	10:1	2-8 bar	10XPL	80	NPT1/2	NPT1/2	30.61
DGGD16	16:1	2-8 bar	16XPL	128	NPT1/2	NPT1/2	19.73
DGGD28	28:1	2-8 bar	28XPL	224	NPT1/2	NPT1/2	11.30
DGGD40	40:1	2-8 bar	40XPL	320	NPT1/2	NPT3/8	7.69
DGGD64	64:1	2-8 bar	64XPL	512	NPT1/2	NPT3/8	4.94
DGGD80	80:1	2-8 bar	80XPL	640	NPT1/2	NPT3/8	3.96
DGGD100	100:1	2-8 bar	100XPL	800	NPT1/2	NPT3/8	3.13
DGGD130	130:1	2-8 bar	130XPL	1040	NPT1/2	M14*1.5	2.40
DGGD175	175:1	2-8 bar	175XPL	1400	NPT3/8	M14*1.5	1.81
DGGD255	255:1	2-8 bar	255XPL	2040	NPT1/4	M14*1.5	1.23
DGGD400	400:1	2-8 bar	400XPL	3200	NPT1/4	M14*1.5	0.79

features

※ Compressed Air driven - no electricity required (connect to normal air compressor)
※ In order to extend the lifetime of the pump, the driving air pressure should not be higher than 8 bar
※ No airline lubricator required
※ Pressures to 640Mpa (6400 bar)
※ Wide range of models with different ratios
※ Built-in-cooling on most models
※ Easy to install, operate and maintain
※ Best price / performance ratio
※ No heat, flame or spark risk and explosion proof
※ Automatic pressure holding, whatever the cause of the pressure drop, the Suncenter pump will automatically start, keep the loop pressure constant

video

v******w

The basic design steps of Suncenter high pressure pneumatic pump are as followed: recognition of its need or purpose, selection of a possible mechanism, analysis of forces, material selection, design of elements (sizes and stresses), detailed drawing, etc. High heat resistant PEEK and POM are selected for its manufacturing

z******n

In order to draw definitive conclusions about the features of Suncenter air driven liquid pump, various tests must be performed. These range from tests on moisture resistance, bending resistance and impact resistance. It is the senior R&D team and delicacy management that make it a success in the market

u******i

Suncenter high pressure pneumatic pump is produced meeting the international standards for electric appliances. It has been sent to the testing organization for quality testing, and it has passed the RoHS, SAA, CB, CCC and ENEC certification. It is the senior R&D team and delicacy management that make it a success in the market

x******c

The design of Suncenter high pressure pneumatic pump meets the market trend of pool accessories. It is created by designers who combine the modern demands for pool accessories with high practicability. It is marketed under our own brand namely Ambition Mods which will soon be a leader in this field

k******u

The safety level of Suncenter air driven liquid pump is guaranteed by a series of tests. It has passed the electric leakage, overload, overvoltage, and capacitive load testings. Its packing is very exquisite that it directly can be a gift

m******l

This product is durable and suitable for long-term use and storage. It is aimed at avoiding the generation of chemicals during smoking

Product Message

*Name

Phone

*E-mail

*Content